2022–2026 Model X Mud Flaps: Fit & Installation Guide
Short answer: Tesheer’s 2022–2026 Model X mud flaps are a four-piece, vehicle-shaped splash-guard set for the front and rear wheel arches. The PP-based flexible composite guards use the vehicle’s existing mounting locations, so no drilling is required. They are intended for refreshed Model X owners who want to reduce the amount of tire-thrown mud, slush, sand, gravel, and road spray reaching the lower doors and rocker-panel area.
What is included in the Model X mud-flap kit?
The Tesheer Model X Mud Flap Set includes four guards: two shaped for the front wheel arches and two shaped for the rear. Clips, fasteners, and installation accessories are supplied with the set. The front and rear pieces have different contours and mounting points, so they should be sorted by position before installation.
| Specification | Tesheer kit |
|---|---|
| Vehicle fit | 2022–2026 Model X |
| Coverage | Two front and two rear wheel-arch guards |
| Material | Black PP-based flexible composite |
| Installation | Existing mounting points; no drilling |
| Hardware | Clips, fasteners, and installation accessories included |
Do these mud flaps fit every Model X?
No. Tesheer lists this set for the 2022, 2023, 2024, 2025, and 2026 Model X. Earlier Model X vehicles can have different wheel-arch shapes or mounting arrangements, so the model name by itself is not enough to establish fit.
Before ordering, check three details:
- Confirm the vehicle’s model year falls within 2022–2026.
- Compare the wheel-arch contour with the installed-product photos.
- Check that the visible factory mounting locations correspond to the holes and tabs shown on the guards.
This is also a separate product from Tesheer’s Model 3 Highland and Model Y Juniper splash-guard kits. Readers with those vehicles should use the dedicated Model 3 Highland mud-flap guide or Model Y Juniper mud-flap guide rather than assuming cross-model compatibility.
What problem do splash guards help address?
A rotating tire can throw water and loose road material rearward. A correctly positioned mud flap extends the wheel-arch barrier behind the tire, helping intercept some of that spray before it travels along the lower side of the vehicle. The four-piece format applies this approach at both axles.
Mud flaps do not make a vehicle dirt-proof or eliminate every stone impact. Their value is more practical: reducing direct tire spray toward lower body surfaces and making routine cleanup easier in wet, snowy, sandy, or gravel-heavy driving environments.
Tesla’s official Model X cleaning guidance still matters after installation. Tesla recommends flushing accumulated mud from wheel wells and panel seams and thoroughly rinsing road salt from the underside, wheel wells, and brakes. Splash guards supplement that maintenance; they do not replace it.
Vehicle-shaped guards versus universal mud flaps
A universal flap typically uses a flatter shape and may require the installer to adapt its position or hardware. A vehicle-shaped set follows the body contour and places its holes around known mounting locations. That makes the finished appearance more integrated and removes the need to create new holes when the kit matches the vehicle.
Tesheer’s set is the vehicle-shaped option. The PP-based composite is molded with position-specific curves and mounting tabs. Buyers who frequently change vehicles or want a flexible DIY material may consider universal options, but Model X owners seeking a close contour and existing-point installation are the clearer audience for this four-piece kit.
How to install 2022–2026 Model X mud flaps
1. Park safely and prepare the wheel arches
Work on a level surface with the vehicle in Park. Clean the wheel-arch edges and mounting area so dirt does not become trapped between the guard and body trim. Tesla’s official Model X mud-flap procedure uses the Very High suspension setting and turns the steering control to provide access to the front working area. Use the instructions appropriate to your vehicle and take care around the suspension and wheel.
2. Sort all four guards before removing hardware
Identify front-left, front-right, rear-left, and rear-right pieces by comparing their curves and holes with the product images. Place each part next to its wheel. This prevents a similar-looking guard from being forced into the wrong position.
3. Remove only the specified factory clips
Use a suitable trim-clip tool and avoid prying against painted surfaces. Keep track of each mounting location. Tesla’s DIY instructions demonstrate access to the wheel-arch liner, but Tesheer’s supplied hardware and product-specific directions determine which fasteners belong with this kit.
4. Test-fit before securing the guard
Hold the mud flap against the wheel-arch contour without installing all fasteners. The holes should align naturally and the inner edge should sit close to the trim. If alignment requires bending, drilling, or heavy force, stop and recheck the piece, side, model year, and vehicle contour.
5. Install the supplied clips and inspect clearance
Secure each guard with the included clips and fasteners at the existing points. Press clips fully into position without overtightening or deforming the composite. After all four are installed, inspect tire clearance through the available steering range and confirm that no guard rubs a tire or hangs loose.
Care after rain, snow, and gravel-road driving
Rinse behind the guards and around the wheel-arch liner rather than cleaning only the exposed surface. Packed mud, leaves, and slush can collect at edges. After winter driving, follow Tesla’s instruction to rinse road salt from the wheel wells and underside. Periodically check that the clips remain seated, especially after deep snow, automated car washes, or rough road use.
Use mild vehicle-wash products and a soft cloth or brush where needed. Avoid striking the guard with a pressure-washer nozzle at very close range. If a flap becomes loose or visibly distorted, inspect the fasteners before continuing normal driving.
Frequently asked questions
Are front and rear Model X mud flaps included?
Yes. The package contains two front guards, two rear guards, and the associated installation accessories.
Does installation require drilling?
No drilling is specified. The kit is designed to use existing mounting locations on compatible 2022–2026 Model X vehicles.
Will the kit fit a 2021 or older Model X?
No earlier fit is claimed. Compare the model year, wheel-arch contour, and mounting layout instead of modifying the guards to fit.
Do mud flaps prevent every paint chip or keep the body completely clean?
No. They can help limit direct tire-thrown spray and debris, but they do not provide complete coverage or guarantee protection from all impacts.
Should the wheel wells still be cleaned?
Yes. Mud, grit, and road salt should still be rinsed from the wheel wells, underside, and areas around the installed guards.
Choose the correct Model X-specific kit
For a 2022–2026 Model X with matching wheel-arch contours, Tesheer’s four-piece set offers front-and-rear coverage, molded PP-composite construction, and installation at existing mounting points. Check the live photos and specifications for the Tesheer Model X Mud Flap Set, or browse more vehicle-specific options in the Model S/X exterior accessories collection.