Tesla Model 3 Highland Mud Flaps: Fit & Install Guide
Short answer: Tesla Model 3 Highland mud flaps are a practical add-on for drivers who want to reduce the mud, slush, sand, salt, and tire spray reaching the car’s lower doors and rocker-panel area. The Tesheer Mud Flaps for the 2024–2026 Tesla Model 3 Highland are a four-piece PP+EPDM set molded for the refreshed wheel arches. They use the vehicle’s existing mounting locations, so installation does not require drilling.
What do Model 3 Highland mud flaps actually do?
Mud flaps, also called splash guards or mud guards, sit directly behind the wheels. Their job is straightforward: interrupt some of the material thrown backward by rotating tires. On a Model 3 Highland, that can mean less direct exposure to road spray and loose debris around the lower doors, rocker panels, and the bodywork immediately behind each wheel.
They do not make the exterior maintenance-free, and they cannot block every stone or splash. Their value is more specific: they add a physical barrier at the point where tire spray leaves the wheel well. Drivers who regularly encounter wet roads, winter slush, sandy shoulders, gravel, or salted pavement are most likely to notice the benefit.
Confirm fit before ordering
The refreshed Model 3 has different wheel-arch shapes and mounting details from the earlier car. Tesheer’s set is designed for the 2024, 2025, and 2026 Tesla Model 3 Highland. It is not intended for the 2017–2023 Model 3.
Use this quick fit check before buying:
- Your vehicle is a refreshed 2024–2026 Model 3 Highland.
- You need guards for all four wheel positions, not only the front pair.
- You prefer an installation that uses existing mounting points.
- You want a black, molded guard rather than a universal flat flap.
If you own another Model 3 generation, shop by the exact model year rather than assuming wheel-arch parts are interchangeable. You can also browse Tesheer’s Model 3 Highland 2024+ collection or narrow the selection to Model 3 Highland exterior accessories.
Tesheer Model 3 Highland mud flap specifications
| Specification | Details |
|---|---|
| Vehicle fitment | 2024–2026 Tesla Model 3 Highland |
| Positions | Front and rear wheel arches |
| Material | PP+EPDM composite |
| Quantity | Four mud flaps |
| Installation method | Existing mounting locations; no drilling |
| Package contents | Front and rear flaps, clips, fasteners, and installation accessories |
Why choose a vehicle-specific four-piece set?
Coverage at both axles
A front-only kit can address spray from the steering wheels, but a four-piece set also places guards behind the rear tires. Tesheer includes a dedicated part for each wheel position. The front and rear pieces are not identical, so lay them out and identify their locations before installation.
Molded contours instead of a universal shape
Universal mud flaps may require trimming, drilling, or improvising a mounting position. This set is molded to follow the refreshed Model 3 wheel arches and align with the original mounting locations. That vehicle-specific shape is the key reason to verify the model year before purchasing.
A balance of rigidity and flexibility
The PP+EPDM composite combines a formed structure with some flexibility for normal driving and changing weather. The matte-black pieces sit low on the body, so they blend with the dark lower trim and tires instead of introducing a bright exterior accent.
How to install no-drill Model 3 Highland mud flaps
The exact sequence should follow the instructions supplied with the product, but a careful installation generally follows these steps:
- Park on a level surface. Put the vehicle in Park, allow the wheel area to dry, and create enough working room around each corner.
- Sort the four pieces. Match the front-left, front-right, rear-left, and rear-right contours to their corresponding wheel arches before removing any factory fastener.
- Clean the mounting area. Remove dirt around the lower wheel-arch liner so debris is not trapped between the flap and the vehicle.
- Remove only the indicated original fasteners. Keep each factory piece organized. Avoid forcing clips or prying against painted surfaces.
- Align the flap with the existing holes. The edge should sit flush against the intended contour without bending or twisting the part.
- Install the supplied clips and fasteners. Seat them evenly and tighten only as directed; overtightening can deform plastic hardware.
- Inspect each corner. Confirm the guard is secure and does not contact the tire through the available steering range.
No drilling means the kit is designed around existing locations, but “no-drill” does not mean “no preparation.” Correct part orientation, clean contact areas, and even fastener seating matter more than rushing through the job.
When are splash guards most useful?
A Tesla Model 3 Highland splash guard set may be a good fit if your commute includes frequent rain, winter road treatment, unpaved parking areas, construction zones, or sandy roadside surfaces. It can also make sense for owners who prefer a subtle functional accessory over a decorative modification.
For a car that only sees clean, dry pavement, the need is less urgent. Consider where you actually drive, how often you clean the lower body, and whether you prefer the appearance of a small molded guard behind each wheel. That practical assessment is more useful than treating mud flaps as mandatory for every owner.
Care after installation
Rinse accumulated mud, salt, and grit from both sides of each flap during regular washes. Periodically check that the clips and fasteners remain seated, especially after winter driving or contact with deep snow. If a part looks misaligned, investigate before continuing to drive rather than simply tightening every fastener.
Also inspect the small space between each guard and the wheel-arch edge. Removing trapped grit helps keep the installation area clean. Avoid harsh tools that could scratch the vehicle or gouge the composite material.
Frequently asked questions
Do these mud flaps fit a 2023 Tesla Model 3?
No. Tesheer’s Model 3 Highland mud flaps are designed for the refreshed 2024–2026 vehicle and are not compatible with the 2017–2023 Model 3 body design.
Does the set include both front and rear splash guards?
Yes. The package contains four mud flaps: two front pieces and two rear pieces. Installation clips, fasteners, and related accessories are also included.
Do I have to drill into the car?
No. The set uses the Model 3 Highland’s existing mounting locations with the supplied hardware. Follow the included instructions and confirm each piece is correctly oriented before fastening it.
What material are the mud flaps made from?
The live Tesheer product specifications list a reinforced PP+EPDM composite. It is molded into separate front and rear shapes for the refreshed Model 3 wheel arches.
Will mud flaps stop all road debris?
No mud flap can block every splash or loose object. These guards are designed to help reduce direct exposure to mud, slush, sand, salt, gravel, and tire spray around the lower body areas behind the wheels.
A practical exterior upgrade for the refreshed Model 3
For the right vehicle, a molded four-piece set offers a straightforward combination of model-specific fit, front-and-rear coverage, and no-drill installation. Check your model year, compare the wheel-arch shape, and review the package contents before ordering. If those details match your car and driving conditions, view the Tesheer mud flaps for the 2024–2026 Tesla Model 3 Highland.