2025–2026 Model Y Juniper Mud Flaps: Fit & Buyer Guide
For a 2025–2026 Model Y Juniper, a four-piece mud-flap kit adds coverage behind both the front and rear wheels, helping reduce the amount of water, grit, road salt, and small debris thrown toward the lower body. The Tesheer Model Y Juniper Mud Flaps are molded from black TPE for the refreshed Model Y body shape and include four vehicle-specific pieces plus installation hardware. They are a practical choice for drivers who regularly encounter wet roads, gravel, snow, or winter road treatment.
What this Model Y Juniper mud-flap kit includes
Tesheer’s live product images show a complete set for the 2025–2026 refreshed Model Y: two front mud flaps, two rear mud flaps, and the mounting hardware needed for installation. Each piece has a different molded contour, so the front, rear, left, and right positions should be identified before any clips or screws are removed.
| Compatible vehicle | 2025–2026 Model Y Juniper with matching wheel-arch shape |
|---|---|
| Material | Black TPE |
| Coverage | Front and rear wheels |
| Package | 4 molded mud flaps plus installation hardware |
| Installation style | Uses the wheel-arch mounting locations shown in the product instructions; no universal cutting or shaping |
Confirm Juniper fitment before ordering
The primary compatibility check is the vehicle generation. “Model Y mud flaps” is too broad because the refreshed Juniper body has different lower trim and wheel-arch contours from the 2020–2024 Model Y. This Tesheer set is shown and labeled for the 2025–2026 refreshed Model Y. It should not be assumed to fit the earlier body style.
Compare your front and rear wheel-arch edges with every product photo, especially if your car has aftermarket side skirts, wheel-arch trim, body repairs, or another mud-flap set already installed. The molded lip should align naturally with the liner and lower body without bending a panel into position.
Four-piece coverage versus front-only mud flaps
Front tires commonly throw spray and grit along the front doors and rocker area, so a front-only set addresses a major exposure point. Tesla’s current Model Y mud-flap listing, for example, describes two front mud flaps with installation hardware. A four-piece kit extends the concept to the rear wheels as well.
| Option | Coverage | Buyer consideration |
|---|---|---|
| Tesheer four-piece molded set | Front and rear | Vehicle-specific Juniper contours and matched appearance at all four wheels |
| Front-only molded set | Front wheels | Focuses on spray reaching the rocker panels and front-door area |
| Universal flexible flap | Depends on installation | May require measuring, trimming, drilling, or custom hardware; appearance is less integrated |
Mud flaps reduce direct spray paths but do not keep a vehicle completely clean or prevent every chip. Coverage changes with tire width, wheel offset, road speed, weather, and the size of the debris. Their main role is to place a barrier close behind each tire.
Why TPE works for molded splash guards
TPE is a flexible molded material rather than a rigid decorative trim. In this application, that flexibility helps the flap tolerate ordinary contact and changing temperatures while maintaining a contoured form. It also creates a low-profile factory-like appearance compared with large flat rally-style flaps.
Material alone does not guarantee unlimited impact resistance or a specific service life. Inspect the pieces after striking deep snow, a curb, or road debris, and replace any flap or fastener that becomes cracked, distorted, or loose.
How to install 2025 Model Y Juniper mud flaps
1. Sort the pieces and hardware
Lay out the two front and two rear pieces beside the matching wheels. Use the molded curves and hole locations—not visual guesswork—to determine each position. Keep all included clips and screws organized.
2. Clean the wheel-arch mounting areas
Remove packed dirt from the liner and lower trim, then dry the area. Tesla’s Model Y mud-flap procedure begins by cleaning the installation area with alcohol and allowing it to dry fully. Follow the Tesheer instructions supplied with this particular four-piece kit whenever its hardware or sequence differs from Tesla’s front-only accessory.
3. Create working room at the front wheels
Turn the steering wheel to provide access to the front liner. A trim-clip removal tool or suitable hand tool can help remove existing fasteners without damaging the liner. Do not force a clip that has not released, and do not substitute longer screws that could contact hidden components.
4. Align before tightening
Place the flap against the wheel arch, confirm that its tabs and holes align, then start the supplied fasteners. Tighten only enough to hold the part securely and evenly. Over-tightening plastic clips can deform the liner or strip the fastener.
5. Check all four wheels
After installation, turn the steering from lock to lock and confirm tire clearance. Make sure every flap sits flush, no fastener protrudes toward the tire, and no liner edge is trapped incorrectly. Recheck the mounting points after the first drives and after the vehicle’s first wash.
Cleaning and seasonal inspection
Debris can collect behind any splash guard. During washing, rinse the wheel wells, flap edges, and panel seams rather than spraying only the visible face. Tesla’s Model Y cleaning guidance recommends flushing mud from wheel wells and panel seams and thoroughly rinsing road salt from the underside, wheel wells, and brakes.
Inspect the mounting hardware after winter, gravel-road use, or contact with packed snow. A loose flap should be corrected promptly so it cannot move toward the tire or rub against painted trim.
Frequently asked questions
Do these mud flaps fit a 2020–2024 Model Y?
No. The live Tesheer product imagery identifies this four-piece set for the 2025–2026 refreshed Model Y Juniper. Earlier Model Y vehicles use a different wheel-arch and lower-body shape.
Does the kit include rear mud flaps?
Yes. The package contains two front and two rear molded mud flaps, along with installation hardware. Confirm each piece’s position before removing factory clips.
Are the mud flaps rigid plastic?
The product is identified as TPE, a molded material with flexibility. It is designed as a close-fitting splash guard rather than a flat universal sheet.
Will mud flaps stop every rock chip and splash mark?
No. They can reduce direct spray and small-debris exposure behind the tires, but results vary with tires, wheel offset, speed, road surface, and weather. They do not make the lower body maintenance-free.
Do I need to drill the vehicle?
The kit is designed around the wheel-arch mounting locations shown in Tesheer’s installation images and includes its own hardware. Follow the supplied instructions and never drill or substitute hardware unless the product documentation explicitly requires it.
Choose the right coverage for your driving
If you drive a 2025–2026 Model Y Juniper and want matching protection behind all four wheels, review the live fitment photos for the Tesheer four-piece TPE mud-flap kit. You can also explore Tesheer’s Model Y Juniper exterior accessories for other generation-specific exterior options. Confirm the vehicle shape before purchase, then install each piece in its correct front/rear and left/right position.