Pink Tesla Model Y Juniper Accessories: What’s in the 8-Piece Kit?
A pink Tesla Model Y Juniper accessories kit is a simple way to create a coordinated exterior accent without choosing separate pieces one by one. The Tesheer 8-piece fuchsia kit combines four door-handle wraps, two side-camera housing covers, and two lower mirror trim strips in one matching high-gloss finish. It is designed for buyers who want a bright, consistent look and prefer molded, peel-and-stick components over a full vehicle wrap.
View the Tesheer Model Y Juniper Fuchsia Accessories Kit to check the current color options, price, and availability.
What comes in the 8-piece Model Y Juniper kit?
The Tesheer kit groups the most visible side accents into a single set. Every component uses the same glossy fuchsia color, so the finish is consistent from the front fender to the rear door.
| Component | Quantity | Where it goes |
|---|---|---|
| Door-handle wraps | 4 | One molded accent for each exterior door handle |
| Side-camera covers | 2 | Around the left and right HW4.0 camera housings, leaving the lenses open |
| Mirror trim strips | 2 | Along the lower edge of each side mirror |
The pieces are molded from automotive-grade ABS and finished with UV-resistant high-gloss paint, according to the live product description. Pre-applied adhesive provides a peel-and-stick installation. This construction gives the accents a defined shape around curved surfaces, which may appeal to shoppers who do not want to measure and cut sheets of vinyl.
Who is this pink Juniper accessory kit for?
This kit is a practical match for a Model Y owner who wants visible color but does not want to change the entire exterior. On a white, black, gray, or silver vehicle, fuchsia creates a clear contrast at three repeated points: handles, mirrors, and camera housings. On another body color, consider whether the combination matches the look you want before installing.
It can also suit a new-car gift buyer because all eight pieces arrive as one coordinated set. The recipient does not need to find separate shades of pink or confirm whether independently purchased accents share the same gloss level. For more vehicle-specific options, browse Tesheer’s Model Y Juniper collection or the narrower Model Y Juniper exterior accessories collection.
Check compatibility before you order
Do not buy by model name alone. The product listing specifies Model Y Juniper 2024–2026 and select 2023 Model Y vehicles equipped with HW4.0; it excludes HW3.0 and HW2.5 vehicles. Because exterior camera housings and trim shapes can differ, compare your vehicle with the product photos and verify the hardware information shown on your car before ordering.
How to check your vehicle
- On the touchscreen, open Controls, then Software.
- Select Additional Vehicle Information and review the listed hardware.
- Compare your side-camera housing, door handles, and mirror lower edge with the close-up images on the Tesheer product page.
- If any shape appears different, pause before removing the adhesive backing.
The Model 3 Highland uses a separate set with different molded shapes. Shoppers with that vehicle should use the Model 3 Highland fuchsia 8-piece kit rather than the Model Y version.
Molded ABS accents versus vinyl color film
Both approaches add color, but the buying experience is different. Pre-shaped ABS pieces arrive ready for their designated locations and create a raised, glossy accent. Vinyl film is thinner and can offer broader customization, but it generally requires careful positioning, trimming, and handling around curves. The Tesheer set is aimed at the buyer who values a coordinated package and straightforward placement more than a nearly flush film finish.
- Choose the 8-piece ABS kit if you want matching molded pieces, defined glossy accents, and no cutting.
- Consider vinyl if you specifically want an ultra-thin finish or plan to cover additional surfaces beyond these eight locations.
- Choose separate accessories if you want to mix colors or accent only one area of the vehicle.
How to install the fuchsia accessory kit
Good preparation matters more than speed. Plan the installation for a dry setting and work on cool, clean surfaces. Avoid applying pieces over wax, dust, or oily residue because contaminants can interfere with the adhesive.
- Clean each location. Use isopropyl alcohol to remove residue, then allow the surface to dry fully.
- Sort and test-fit all eight pieces. Match left and right components and confirm their orientation before peeling any liner.
- Align first, then press. Start from a clear edge or contour. Press each piece firmly for about 30 seconds, paying attention to the perimeter.
- Inspect the camera openings. Confirm that each cover surrounds only the outer housing trim and that the lens remains fully unobstructed.
- Allow time for the adhesive to set. The product instructions recommend avoiding a car wash for 24–48 hours after installation.
Before pressing the door-handle pieces permanently, operate every handle and check that the accent follows the intended outline. For mirror trim, view the car from both the front and rear to confirm that the curved strip sits evenly along the lower edge.
Care and removal considerations
For routine care, wash the accents with the same gentle approach used on the surrounding exterior and avoid prying at their edges. If you decide to remove them later, the product instructions suggest low heat from a hair dryer to soften the adhesive, followed by slow lifting from one edge. Work patiently and clean remaining residue with rubbing alcohol. These are semi-permanent accents rather than quick-swap decorations, so repeated removal and reinstallation is not their intended use.
Frequently asked questions
Is fuchsia the same as pink in this Tesheer kit?
Tesheer names the product fuchsia, while its current selectable variant is labeled Pink. The product photos show a vivid, glossy pink-fuchsia tone. Use the live images as the best guide because screen settings can change how color appears.
Does the 8-piece set include mirror caps?
No. It includes two narrow trim strips for the lower edges of the side mirrors, not full mirror caps. The other six pieces are four door-handle wraps and two side-camera housing covers.
Will the camera covers block the side-camera lenses?
The molded covers are designed to decorate the outer HW4.0 camera housings while leaving the lens openings exposed. During installation, visually confirm that neither lens is obstructed before driving.
Can I install the kit without cutting or special tools?
Yes. The eight molded pieces have pre-applied adhesive and do not require cutting. Cleaning supplies are useful for surface preparation, and every piece should be test-fitted before the backing is removed.
Can I use this set on a Model 3 Highland?
No. Tesheer lists a separate Model 3 Highland kit because its component shapes differ. Select the product made for your exact vehicle rather than adapting the Model Y Juniper set.
A coordinated color upgrade in one box
The Tesheer fuchsia 8-piece kit is most compelling for a buyer who wants a repeatable pink accent across the sides of a compatible Model Y without shopping for three unrelated products. Verify the hardware and exterior shapes, decide whether a raised high-gloss finish suits your style, and test-fit every part before installation. If that combination fits your goal, see the live Tesheer kit and available colors.