What Comes in an Orange Model 3 Highland Exterior Kit?
An orange Model 3 Highland accessories kit is a coordinated way to add color to the car’s door handles, side-camera housings, and mirrors without choosing separate pieces one at a time. Tesheer’s eight-piece exterior kit includes four high-gloss orange door-handle covers, two HW4 side-camera housing covers, and two slim mirror-trim strips for the 2024–2026 Model 3 Highland. It is intended for buyers who want a bold, matched accent package and are willing to confirm the refreshed body shape before installation.
The Tesheer Orange Model 3 Highland Accessories Kit may suit an owner who prefers a molded ABS upgrade over applying several separate vinyl accents. The key buying decision is fit: this listing is for the refreshed Model 3 Highland, not the 2017–2023 Model 3 and not the Model Y Juniper.
Quick answer: what comes in the eight-piece kit?
The kit covers three visible exterior zones with one matching high-gloss orange finish. The eight pieces are divided across both sides of the vehicle:
- Four door-handle covers: one molded piece for each flush exterior handle
- Two HW4 side-camera covers: one for each front-fender camera housing
- Two mirror-trim strips: one slim accent for each side mirror
The product listing identifies the material as automotive-grade ABS with a high-gloss painted surface and pre-applied adhesive. Because the components are shaped for specific exterior parts, a careful dry fit matters more than model-year wording alone.
Fitment: which Model 3 does this orange kit match?
| Vehicle | Expected fit | What to verify |
|---|---|---|
| 2024–2026 Model 3 Highland | Listed application | Refreshed flush handles, mirror shape, and matching HW4 camera housing |
| 2017–2023 Model 3 | Not listed to fit | Earlier handles, mirrors, and side-camera housing use different contours |
| Model Y Juniper | Requires a separate kit | Choose the Model Y-specific pieces rather than adapting this set |
| Model S or Model X | Not listed to fit | Exterior component shapes are different |
Before peeling any backing, place every component over its intended area. All edges should follow the factory contour without forcing, rocking, or crossing a panel gap. If you own the refreshed Model Y, use the separate orange Model Y Juniper accessories kit.
Molded ABS kit or vinyl accents?
A molded kit and vinyl can create a similar color theme, but they deliver it differently. Molded ABS pieces arrive shaped for the target component and add a raised layer. Vinyl is thinner and can follow complex curves, but neat results depend heavily on stretching, edge work, and installation technique.
- Choose molded covers if you want matching, removable components with defined edges and a glossy three-dimensional appearance.
- Choose vinyl if the lowest possible profile matters and you are comfortable applying and trimming film.
- Choose neither if you prefer the factory exterior with no added layers around handles, mirrors, or camera housings.
The Tesheer kit is a styling accessory; it does not change how the handles, mirrors, or cameras are designed to operate. Buyers should prioritize clean alignment and unobstructed functional areas over color coverage.
Camera-cover checks are essential
The side-camera pieces are shaped to accent the outer HW4 housing, not the lens. Tesla’s current Model 3 guidance says cameras must remain clean and free of obstructions, and it notes that mounted objects or adhesive products can contribute to camera-visibility alerts. After test-fitting, confirm that the camera opening and any adjacent functional area remain completely exposed.
- Identify the left and right camera pieces before removing adhesive backing.
- Align the molded opening around the housing while keeping the lens fully visible.
- Check the view from several angles; no orange edge should intrude into the opening.
- After installation, inspect both sides again before driving.
- If a camera warning appears or any view looks obstructed, stop and correct or remove the interfering piece.
This inspection is more useful than assuming a cover is correct merely because the vehicle year appears on a listing. Hardware transitions can vary, so the actual housing shape is the final reference.
How to install the orange Model 3 Highland kit
1. Clean and dry every surface
Wash away dust and road film, then dry the handles, camera housings, and mirror edges completely. Avoid installing over wax, sealant residue, or moisture because those layers can prevent consistent adhesive contact. Use only surface-preparation products suitable for the vehicle’s exterior finish.
2. Sort and dry-fit all eight pieces
Separate the four handle covers, two camera pieces, and two mirror strips. Match left and right parts, then test every piece without exposing the adhesive. Check door-handle movement, panel clearances, mirror-trim alignment, and camera openings.
3. Apply one component at a time
Peel the backing only after alignment is clear. Lower the piece into place without sliding it across the paint, then press evenly along the center and edges. Do not stack extra tape or force a part that does not sit flush.
4. Perform a functional inspection
Operate every door handle, fold and unfold the mirrors if equipped, and inspect both camera openings. Follow the adhesive instructions supplied with the product before washing the vehicle or exposing the edges to strong water pressure.
Who is this orange exterior kit for?
This set is most relevant to a 2024–2026 Model 3 Highland owner who wants a noticeable orange accent repeated across several exterior touchpoints. It can also simplify shopping because the finish is coordinated across eight pieces rather than assembled from separate listings.
A buyer who wants a softer color can compare Tesheer’s pink Model 3 Highland accessories guide. For other compatible products, browse the Model 3 Highland collection and verify the model year and component shape on each product page.
Frequently asked questions
Does this kit fit a 2023 Model 3?
No. Tesheer lists this orange eight-piece kit for the refreshed 2024–2026 Model 3 Highland. The earlier 2017–2023 Model 3 uses different exterior component contours.
How many pieces are included?
The kit contains eight pieces: four door-handle covers, two HW4 side-camera housing covers, and two side-mirror trim strips.
Will it fit a Model Y Juniper?
No. Model Y Juniper owners should choose the separate Model Y-specific orange kit because its handles, mirrors, and camera housings are shaped differently.
Do the orange camera covers go over the lens?
No. The covers are intended for the outer HW4 camera housing. The lens and surrounding functional opening must remain fully visible, clean, and unobstructed.
Can the kit be installed without removing factory parts?
The listing describes peel-and-stick components with pre-applied adhesive. Dry-fit each piece first and do not remove, drill, or alter factory exterior components to make a mismatched piece fit.
Build a coordinated orange Highland exterior
The Tesheer kit gives compatible Model 3 Highland owners a single matched set for four handles, two side-camera housings, and two mirrors. Its value comes from coordinated color and model-specific shapes, so confirm the refreshed vehicle layout and protect all camera openings during installation. View the Orange Model 3 Highland 8-Piece Accessories Kit and select the orange variant after checking your vehicle.
For current vehicle guidance, review Tesla’s Model 3 camera limitations and obstruction guidance and parts and accessories guidance.